pdf standard test method for tensile properties of

(PDF) ASTM E8-04 - Tension Testing of Metallic Materials

An American National Standard Designation:E 8 04 American Association State Highway and Transportation Officials Standard AASHTO No.:T68 Standard Test Methods for Tension Testing of Metallic Materials1 This standard is issued under the fixed designation E 8; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of ASTM C158 Standard Test Methods for Strength of Glass by ASTM C158 Glass Modulus of Rupture and Flexural Properties. Test Method A Procedure. Refer to the standard for the proper way to cut, size, count and prepare the specimen. Position the specimen in the bend fixture. Apply load to the specimen, as specified for annealed glass and prestressed glass, at a constant rate until the specimen breaks.

ASTM D638 - 14 Standard Test Method for Tensile Properties

D882 Test Method for Tensile Properties of Thin Plastic Sheeting. D883 Terminology Relating to Plastics. D1822 Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials. D3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite Materials. D4000 Classification System for Specifying Plastic Materials ASTM D638 :Standard Test Method for Tensile Properties of Dec 15, 2014 · ASTM D638, 2014 Edition, December 15, 2014 - Standard Test Method for Tensile Properties of Plastics This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. ASTM D638 Standard Test Method for Tensile Properties of ASTM D638 specifies methods for testing the tensile strength of plastics and other resin materials and for calculating their mechanical properties, and outlines accuracy requirements for the test frames and accessories used. This test method uses dumbbell-shaped specimens with either a

ASTM D638-02a.pdf - Google Docs

Standard Test Method for Tensile Properties of Plastics Ths standard is issued under the fixed designation D 638; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A Standard Test Method for Elastic Properties of Standard Test Method for Elastic Properties of Elastomeric Yarns (CRE Type Tensile Testing Machines)1 This standard is issued under the xed designation D 2731; the number immediately following the designation indicates the year of original adoption or, in Standard Test Method for Tensile Properties of 1.2 This test method covers the measurement of tensile strength and elongation of geotextiles and includes directions for the calculation of initial modulus, offset modulus, secant modulus, and breaking toughness. 1.3 Procedures for measuring the tensile properties of both conditioned and wet geotextiles by the wide-width strip method are included. 1.4 The basic distinction between this test method and

Standard Test Method for Tensile Properties of Glass

Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics1 This standard is issued under the xed designation D 2343; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. Standard Test Method for Tensile Properties of Paper and More D09.01 Standards Related Products Standard References. Significance and Use. 4.1 The tensile properties measured in this test method are fundamental properties associated with the manufacture, or end use, or both, of paper and paper products. It is possible for the varity of products to be influenced by, or indicative of:the type fibers used or the treatment of the fibers, or both, in a particular paper:or Standard Test Methods for Tension Testing of Metallic 1.3 Exceptions to the provisions of these test methods may need to be made in individual specications or test methods for a particular material. For examples, see Test Methods and Denitions A370 and Test Methods B557, and B557M. 1.4 Room temperature shall be considered to be 10 to 38°C [50 to 100°F] unless otherwise specied.

Standard Test Method for Tensile Properties of Yarns by

Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method1 This standard is issued under the xed designation D 2256; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A